Fender®

What is Micro-Tilt™?

 

Four-bolt neck attachment with Micro-Tilt on a Stratocaster. In the neck pocket in the lower half of the photo, the round Micro-Tilt mechanism is separate from the four neck "bolt" holes and is seen here with its Allen screw protruding from its center hole. The Allen screw presses against the circular metal plate set into the underside of the butt end of the neck, as seen in the upper half of the photo.
Four-bolt neck attachment with Micro-Tilt on a Stratocaster. In the neck pocket in the lower half of the photo, the round Micro-Tilt mechanism is separate from the four neck “bolt” holes and is seen with its Allen screw protruding from its center hole. The Allen screw presses against the circular metal plate set into the underside of the butt end of the neck, as seen in the upper half of the photo.

There are now more than two dozen Fender electric guitar and bass models that feature Micro-Tilt neck adjustment. This is a feature originally introduced in the early 1970s as an easy means of adjusting the angle of the neck in relation to the instrument body.

Three-bolt neck attachment with Micro-Tilt on a Telecaster Deluxe. In the neck pocket in the middle portion of the photo, the center hole in the round Micro-Tilt mechanism actually accommodates the lower of the three neck attachment “bolts,” while the smaller hole just to the left of it contains the Allen screw used to make neck-tilt adjustments. The upper portion of the photo shows the metal plate mounted on the underside of the butt-end of the neck, against which the Allen screw presses; the lower portion of the photo shows the neck plate, with three large holes for the neck attachment bolts and a single smaller hole near the bottom that allows access to the Allen screw.
Three-bolt neck attachment with Micro-Tilt on a Telecaster Deluxe. In the neck pocket in the middle portion of the photo, the center hole in the round Micro-Tilt mechanism actually accommodates the lower of the three neck attachment “bolts,” while the smaller hole just to the left of it contains the Allen screw used to make neck-tilt adjustments. The upper portion of the photo shows the metal plate mounted on the underside of the butt-end of the neck, against which the Allen screw presses; the lower portion of the photo shows the neck plate, with three large holes for the neck attachment bolts and a single smaller hole near the bottom that allows access to the Allen screw.
Micro-Tilt is a simple leverage mechanism. Through a small hole in the neck plate, a small Allen screw can be used to increase neck angle. Tightening the screw makes it protrude beyond the surface of the neck pocket, pushing on a metal plate mounted on the bottom of the neck heel and thus slightly increasing the neck angle.

Today, there are Micro-Tilt mechanisms for four- and three-bolt necks (bolt in this instance being an enduring Fender misnomer; necks are fixed to the bodies with screws). On four-bolt models, the metal plate on the neck heel is separate from the holes for the neck bolts. On three-bolt models, the bottom neck-mounting bolt passes through the plate, but the adjustment works the same way. In either design, the neck-mounting bolts must be loosened slightly in order for Micro-Tilt adjustments to me made, then tightened once the desired neck angle is achieved.

OK, but why would I need to adjust my guitar’s neck angle in the first place?

Many players will never need to adjust neck angle. But there are circumstances in which the adjustment becomes necessary. Mainly, the angle at which the neck is seated in the neck pocket affects how low the bridge must be set in order to achieve optimal playing action (string height above the fingerboard).

If the neck angle is too shallow, the action can still be too high even after setting the bridge (or bridge saddles) as low as possible. Perhaps the original angle wasn’t ideally set in the first place. More often, replacing the bridge or combining a neck and body from two different instruments can be the culprit. When replacing the bridge with a shorter one or a taller one, a neck angle adjustment might very well be necessary. In any case, if the string height isn’t comfortable even after a good setup, neck angle adjustment might be helpful.

To make this a simple DIY adjustment, Fender introduced Micro-Tilt in 1971 when it switched the Stratocaster® from four- to three-bolt neck plates. Other Fender guitars of the early 1970s, such as the Telecaster Custom and Telecaster Deluxe, subsequently featured three-bolt Micro-Tilt necks.

Today, Fender offers several instruments equipped with Micro-Tilt. These have neck plates with three- and four-bolt neck plates, and they include the Classic Series ’70s Stratocaster, ’72 Telecaster® Custom, ’72 Telecaster Thinline and ’72 Telecaster Deluxe; most American Deluxe Stratocaster and Telecaster models; American Standard Stratocaster and Telecaster models; and several Fender Select models.

 

Shop for these Fender Micro-Tilt-related items:

Modern-style Micro-Tilt adjustment screw
Neck-mounting hardware
Neck plates
Necks and bodies

And, check out this Fender University video for more details on Micro-Tilt:

Tags:

Leave a reply

Have a question?
Please direct your questions to consumerrelations@fender.com or visit the Fender Forums.

comments powered by Disqus

« Previous Post Next Post »